2
http://journals.hsu.ac.ir/asfm
Advances in Solid and Fluid Mechanics. - Journal articles for year 2019, Volume 1, Number 1Yektaweb Collection - https://yektaweb.comen2019/4/12Size-dependent Response of Rectangular Micro-plates Subjected to Random Base Excitation Incorporating the Packaging Effect
http://journals.hsu.ac.ir/asfm/browse.php?a_id=27&sid=1&slc_lang=en
The objective of the present paper is to investigate the size-dependent response of a fully clamped rectangular micro-plate under random base excitation. The size-dependent Kirchhoff's plate model based on the modified couple stress theory is utilized in the theoretical formulation. The equations of motion which account for the packaging effect and axial residual stresses are derived using Hamilton's principle. To find the spectral density and mean square value of the micro-plate deflection, the standard modal summation method is employed where the micro-plate mode-shapes are extracted using the extended Kantorovich method. A convergence study is conducted to find the number of modes which must be included in the response. It is found that using the first six symmetric mode-shapes for the present micro-plate leads to very accurate results, while single-mode solution gives the mean square value of the response with a maximum error of 10%. Furthermore, the results reveal that the size effect on the mean square value of the mid-point deflection is usually negligible when the ratio of the plate thickness to its material length scale parameter becomes larger than 15.Amir Reza AskariStudy on Ultimate Capacity of Offshore Jacket Platforms Considering the Effects of General and Local Buckling of the Elements
http://journals.hsu.ac.ir/asfm/browse.php?a_id=38&sid=1&slc_lang=en
The ultimate capacity of offshore structures including jacket type offshore platforms is used to achieve structural performance levels and determine their ductility. Accurate estimation of this parameter is of great importance. Formation of fatigue cracks at the joints, corrosion of members, environmental loads and damages caused by accidental dynamic loads such as impacts of vessels and floating bodies will result in change of the ultimate capacity of these structures over time of their life. These cases should be considered in calculating the ultimate capacity of the offshore platforms at any given time of their life. However, accurate modeling of the global and local buckling of compression members is important at any time of calculating the ultimate capacity. Buckling modes and deformations due to local buckling will be considered, if the compressive braces are modeled by Shell or Solid elements and the imperfections are applied. The purpose of this paper is to achieve the correct compressive behavior of compression members. ABAQUS finite element computer software is used for this purpose. The buckling envelope derives from Marshall Strut theory defines the post-buckling damaged elasticity model and the hysteretic loop response. Finally, by using this modified behavior in Frame elements, the effects of local buckling in compressive braces can be considered.Mohammad Reza TabeshpourContact Problem of an Elastically Dissimilar Symmetric Wedge with a Half Plane Including Convective Effect
http://journals.hsu.ac.ir/asfm/browse.php?a_id=31&sid=1&slc_lang=en
In this paper, the contact problem between a dissimilar wedge and an elastic half-plane is studied. The investigated problem considers the convective effect which resembles a non-Hertzian contact problem. Unlike the previous studies, which focused to find the solutions of the singular integral equations, here, the contact problem is formulated based on the Muskhelishvili complex potential method for the two-dimensional elasticity. The problem formulation is converted into a Riemann-Hilbert problem. Finally, we derive a closed-form solution for the Riemann-Hilbert problem in terms of the Muskhelishvili complex potential. According to the results, the convective effect increases the contact half-length by factor of 35% for the case of maximum material dissimilarity. Moreover, the complex potential for the similar materials condition is extracted in accordance with the previous studies.Yadolah AliniaInvestigating and comparing the effect of process optimization and use of a grinding aid in improving the performance of cement mill department in a cement plant
http://journals.hsu.ac.ir/asfm/browse.php?a_id=36&sid=1&slc_lang=en
Producing cement with appropriate quality and by spending the minimum cost, applying solutions including process optimization and use of grinding aid are suggested. This paper compares and investigates the effect of process optimization and use of grinding aid on the operational capacity and blaine of final product in two cement mill departments in a cement plant. The results of a specific grinding aid test and its effect on the quantity and quality of the final product were compared with the results obtained from process optimization of cement mill lines 1 and 2 of a cement plant including optimization of the arrangement and tonnage of the charge of balls. The results suggested that the operational capacity of cement mill of lines 1 and 2 when optimizing the process conditions increased by around 9.4 and 15%, and the blaine of the final product of the department rose by about 4.6 and 4.3% respectively compared to the case of using the grinding aid. It should be noted that performing the grinding aid test in relation to the initial conditions only resulted in enhanced operational capacity of cement mills, and had no significant effect on the parameter of quality (blaine). On the other hand, performing the process optimization had positive effects on both quantity and quality.Behnam NasrollahzadehAn Improved Empirical Correlation for Boundary Layer Transition Considering the Effects of Both the Streamwise Pressure Gradient and Freestream Turbulence Intensity
http://journals.hsu.ac.ir/asfm/browse.php?a_id=28&sid=1&slc_lang=en
ABSTRACT: the empirical correlation for prediction of the onset of boundary layer transition, presented previously by Taghavi et al., was extended by taking into account both the effects of the streamwise pressure gradients and the freestream turbulence intensity. The correlation was derived based on experimental data of transitional boundary layers subjected to different freestream turbulence intensities and streamwise pressure gradients, obtained by authors and other researchers. The author’s experiments were carried out in two different free stream turbulence levels and four different pressure gradients. A single hot-wire probe was used for measurements of instantaneous flow velocities within the boundary layer. Experiments were conducted in an open circuit wind tunnel of suction type. For each pressure gradient in a distinct free stream turbulence level, the mean longitudinal velocity and root mean square, RMS, of the velocity fluctuations were obtained at several streamwise locations. Experimental results were used to determine variations of streamwise skin friction coefficient and boundary layer shape factor versus the local Reynolds number. Based on the available measurements and mathematical models, an improved empirical correlation was developed. Comparisons with other existing empirical correlations show that the new correlation was more consistent with experimental data.Mahmoud SalariInvestigating migration velocity in the clinker cooler one stage electrostatic precipitator (made by ELEx, Hamon, and FLSmith Co.)
http://journals.hsu.ac.ir/asfm/browse.php?a_id=34&sid=1&slc_lang=en
The rapid advances in human societies over the past decades have resulted in fast development of steel, cement, and other industries. Cement is one of the most important industries which plays a significant role in the development and prosperity of any country and worldwide. On the other hand, cement factories are among the major environmental plights and source of contamination. Accordingly, one of the main issues of these factories is controlling and preventing excessive emission of contaminants. Electrostatic precipitators are among the most important devices for controlling air pollution. One of the most important influential parameters affecting the efficiency of dust collection in the design of the electrostatic precipitator is the migration velocity. In this research, this parameter was studied in the electrostatic precipitators of ELEx, Hamon, and FLSmith companies, which are responsible for collecting the dust from Clinker coolers in cement factories. The results of the research suggested that the range of this parameter under the mentioned conditions was obtained as 8.7-11.5 Also, it can be stated that with elevation of the efficiency of mechanical dust collection of the equipment, one can achieve a better efficiency. This can be realized by properly exploiting chemical engineering, mechanical engineering, electricity engineering, as well as the experiences of scholars, thereby reducing costs, increasing the useful lifetime of equipment, and preventing environmental pollution.Amin Emami Razlighi